JVD Graphics - Just Vinyl Decal Graphics Banner
Menu Bar - Home
Order Graphics Here
 
Products
Discounts / Specials
Automotive
3rd Brake Light Covers
Body Kit Graphics
Brake Caliper Stickers
Bumper Inserts
Eyebrows
G2 Caliper Paint
Pinstripes
Roll Call Kits
Tribal Designs/Letters
Vinyl Sheets/Rolls
Windshield Banners
Custom Order?
Miscellaneous
College Decals
College Decals
Greek Lettering
Performance Parts
Performance Parts
Miscellaneous
A-Frame Signs
Animals
Banners of All Sizes!
Cartoons
Corporate Logos
License Plates
Motorcycles
Patriotic
Police & Fire Dept
Professional Sports
Racing & Nascar
Retail Signs
Scrapbooking Images
Shilouette Images
Sign Shapes
Southern Pride
TV Characters & Shows

Information
Vinyl Color Choices

Affiliates
Become An Affiliate!
Dealers
"Kings" Playing Cards
LancerShop.com
LeatherSeats.com
Performance Tuning
RIPPMods
StreetUnit.com
What A Day Clothing
Car Clubs / Boards
Club3G.com

Photo Gallery

Contact Me
Email Me
JVD Graphics

 

Solution Graphics

Application Instructions for:
Small Decals
(12" width or less)
Large Decals
(+12" width)
Caliper Stickers
**Click above links to go to instructions

Requirements/Equipment:
Paper Towels
Window Cleaner
Masking Tape
Squeege/ID Card

Shaded area (50-90 degrees out)
Clean Wax-Free Application Surface

Smaller Sized Decals (12" or under)
Step 1: Clean Surface
Step 1: Clean Surface

Clean surface thoroughly to remove contaminents/wax and result in a clean smooth surface. This is vital, otherwise the sticker could loose its adhesiveness.

Step 2: Place Sticker
Step 2: Place Sticker

Place sticker on desired surface and location. Place two or more pieces of masking tape along the top of the decal to create a hinge.

Step 3: Remove Bottom Portion of Graphic
Step 3: Remove Bottom of Graphic

Remove the bottom portion of the decal, resulting in the graphic to stick to the adhesive tape.

Step 4: Apply Decal
Step 4: Apply Decal

Now carefully replace the graphic onto the surface and rub it as well as possible along with the use of a plastic ID card or squeege to ensure a strong adhesion. Rub from the center of the decal out to the edges to remove air bubbles.

Step 5: Remove Transfer Tape
Step 5: Remove Transfer Tape

For the last step, slowly remove the clear transfer tape to expose the surface of the new decal. Do not pull straight out, pull the transfer paper at an angle slowly.

Done! Result: Brand New Decal!
Done

Now show off your brand new decal!

Larger Sized Decals (12" or over)
Step 1: Clean Surface
Step 1: Clean Surface Clean surface thoroughly to remove contaminents/wax and result in a clean smooth surface. This is vital, otherwise the sticker could loose its adhesiveness.
Step 2: Remove Bottom Portion of Graphic
Step 2: Remove Bottom Portion of Decal Remove the bottom portion of the decal, resulting in the graphic to stick to the adhesive tape.
Step 3: Decal Preparation
Step 3: Spray Mixture on Surface

With a small soap/water mixture (small squirt of dish soap in a large spray container) or Windex (anything to create a slippery surface) spray the bottom of the decal on the adhesive tape, along with the surface where the decal will be applied.

Step 4: Apply / Align Decal
Step 4: Apply/Align

Now carefully place the graphic onto the surface and align/realign it as desired.

Step 5: Apply / Align Decal
Step 5: Apply/Align Decal

With a squeege or plastic ID card, remove as much of the wet solution and air bubbles out of the graphic. Be careful not to move the decal out of alignment.

Step 6: Wait / Remove Transfer Tape
Step 6: Wait/Remove Tape

Wait for 2-4 hours (or more depending on temperature outside) or use a hair dryer to allow the decal to dry. After the decal has dried, slolwly remove the clear transfer tape to expose the surface of the new decal. Do not pull straight out, pull the transfer paper at an angle slowly. if the decal happens to lift up, repeat steps 5+6.

Done! Result: Brand New Decal!
Done Now show off your brand new decal!
Caliper Stickers
Step 1: Clean Surface
Step 1: Clean Surface

IMPORTANT: MAKE SURE THE SURFACE OF THE CALIPER IS COLD.
If the calipers are not freshly painted, clean the surface thoroughly to remove contaminents and result in a clean smooth surface. This is extremely important, otherwise the sticker could loose its adhesiveness.

Step 2: Remove Backing
Step 2: Remove Backing Remove the bottom portion of the decal, resulting in the graphic to stick to the adhesive tape.
Step 3: Line Up Decal
Step 3: Apply

Simply line up the decal exactly how you want it and place it onto the caliper, rubbing it as well as possible to ensure a strong adhesion. Rub from the center out to remove air bubbles.

Step 4: Remove Transfer Tape
Step 4: Remove Tape

For the last step, slowly remove the clear transfer tape to expose the surface of the new decal. Do not pull straight out, pull the transfer paper at an angle slowly.

Done! Result: Brand New Decal!
Done Now show off your brand new decal!
Large Pic Done

 

©JVD Graphics. 2005

Note: Copyright © All rights reserved. Some of the logos included on this site are the trademarks or registered trademarks of their respective companies,and are provided as a convenience only for their lawful use. It is the expressed intent of JVD Graphics that any unauthorized use of these items by the purchaser shall be the sole responsibility of the purchaser. The purchase of any item from JVD Graphics is not authorized for the use of any specific logo or trademark. By purchasing said logos, you are indicating that you have authority to use the artwork.